ID TECH Omni User Manual Page 17
- Page / 64
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
13
Magnetic Stripe Formatting Selections (Group D)
Magnetic stripe output can also be formatted with the addition of preambles,
postambles, and terminator characters. The settings below will augment mag-
netic stripe data read by the Omni. A fully-formatted message block refl ects
the following model:
{Preamble}{T1 ID}{T1 Data}{Track Separator}{T2 ID}{T2 Data}{Track
Separator}{T3 ID}{T3 Data}{Terminator}{Postamble}
1. Enter MAGNETIC STRIPE FORMATTING SETUP MODE by typing
/E/D/FD
.
2. Press
<ENTER>
.
The reader should beep twice.
3. Type the two-character selection code for the feature you wish to change.
4. Press
<ENTER>
.
The reader should beep twice.
5. Type the one-character code for the change you wish to make.
6. Press
<ENTER>
.
The reader should beep twice.
7. Save the change and exit the Magnetic Stripe Setup Mode by typing
DZ
.
8. Press
<ENTER>
.
The reader should beep four times.
Note: To review the group’s current setting(s), type DY<ENTER> while in the Mag-
netic Stripe Formatting Setup Mode. To reset the current setting(s) to its group default,
type DX<ENTER> while in Formatting Mode.
Magnetic Stripe Terminator Character
Enter and LF, Enter, Line Feed, or None: For some applications, it may be
convenient to end a string of magnetic stripe data with a terminator character.
For example, with keyboard entry, it is common to have the operator signify
the end of the data input with the “Enter” keystroke. The terminator character
serves this function.
SELECTION CODE: D1
ENTER and Line Feed A
ENTER B
Line Feed C
None D
EXAMPLE:
To set the magnetic stripe terminator character to Line Feed, enter:
/E/D/FD<ENTER>D1<ENTER>C<ENTER>DZ<ENTER>
SELECTION CODE: D1
ENTER and Line Feed A
ENTER B
Line Feed C
None D
ENTER and Line Feed A
ENTER B
Line Feed C
None D
- Keyboard Wedge 1
- USB/Keyboard Wedge 1
- Combined Bar Code 1
- Magnetic Stripe Reader 1
- Agency Approved 2
- Limited Warranty 2
- Table of Contents 3
- Section 1 5
- INTRODUCTION 5
- Description 5
- Section 2 6
- INSTALLATION 6
- Host Connections 6
- Section 3 7
- OPERATION 7
- Operating Procedure 7
- Section 4 8
- CONFIGURATION 8
- Configuration Setup Procedure 8
- Default Settings 10
- General Selections (Group B) 11
- Beep Volume 12
- Intercharacter Delay 12
- Interblock Delay 12
- Language 13
- Code/Track ID 13
- Scan Verification 13
- Function Code 13
- Code ID Definition (Group I) 14
- Bar Code Terminator Character 15
- Bar Code Preamble 16
- Bar Code Postamble 16
- Magnetic Stripe Preamble 18
- Magnetic Stripe Postamble 18
- Bar Code Selections 19
- Code 39 Settings: 20
- Check Digit 21
- Send Start/Stop Characters 21
- Interleaved 2 of 5 Settings: 22
- Industrial 2 of 5 Settings: 23
- FEBRABAN Conversion: 24
- Code 128 Setting: 24
- Codabar Settings: 25
- MSI/Plessey Settings: 26
- Telepen Setting: 26
- Retail Bar Codes (Group G) 27
- UPC Settings: 27
- Enable/Disable UPC-E 28
- Send Number System Digit 28
- Send Check Digit 28
- UPC-E Expansion 28
- EAN Settings: 30
- Read Two-Digit Addendum 31
- Read Five-Digit Addendum 31
- Addendum Required 31
- Add Separator Space 31
- Track Selection 32
- Send Start/Stop Sentinel 32
- Track Separator 33
- Section 5 35
- DATA EDITING 35
- Data Fields 36
- Data Editing Formulas 37
- The Formula Sequence 38
- Data Editing Commands 40
- Select Code ID(s) 41
- Set Length 41
- Match String 42
- Create a Data Field 42
- Search for a Data String 43
- Add a Data Field 43
- Time Delay 44
- Delete One Formula 44
- Omni Data Flow 45
- 76440057320712 46
- *AST798X* 47
- EXAMPLE THREE 48
- Section 6 49
- TROUBLESHOOTING 49
- General Procedures 49
- Keyboard Interface Problems 50
- Appendix A 52
- BAR CODE DEFAULT SETTINGS 52
- Appendix B 55
- Appendix C 56
- FUNCTION CODE TABLE 56
- Appendix D 57
- FORMATS 57
- Card Format 57
- Appendix E 61
- CONNECTOR PIN-OUTS 61
- Appendix F 62
- USB/KEYBOARD INTERFACE 62
- Installation 62
- Operation 63
- 10721 Walker Street 64
- Cypress, California 90630 64
- (714) 761-6368 64
Related products and manuals for Magnetic card readers ID TECH Omni
(4 pages)© 2020, manymanuals.com. All rights reserved. | 0.948 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals