ID TECH Omni User Manual Page 28
- Page / 64
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
24
Enable/Disable UPC-E
UPC-E is a special version of the UPC-A specifi cation. It is a fi xed format
symbology and there are no variations allowed. If disabled, the data from the
symbology will be disregarded.
SELECTION CODE: G1
UPC-E Enable C
UPC-E Disable D
Send Number System Digit
The fi rst encoded digit in the UPC-A symbol is the number system digit. If
enabled, the fi rst digit of the transmitted data stream is the number system
digit followed by the manufacturer’s number. If disabled, then the fi rst digit
transmitted is part of the manufacturer’s number.
SELECTION CODE: G1
Send Number Digit E
Do Not Send Number Digit F
Send Check Digit
The check digit is mandatory in the UPC symbology. If enabled, the reader
will send the decoded check digit as the last character in the data stream trans-
mitted. If not, the check character will be suppressed before transmission.
SELECTION CODE: G1
Send Check Digit G
Do Not Send Check Digit H
UPC-E Expansion
The UPC-E symbology uses a special algorithm to suppress zeros in the
encoded data. The suppressed information can be restored by either the Omni
reader or the host system. If enabled, the reader will restore the data to its
original format. If the host system is set up to do the expansion, then this op-
tion should not be used.
SELECTION CODE: G1
Expand UPC-E I
Do Not Expand UPC-E J
SELECTION CODE: G1
UPC-E Enable C
UPC-E Disable D
UPC-E Enable C
UPC-E Disable D
SELECTION CODE: G1
Send Check Digit G
Do Not Send Check Digit H
Send Check Digit G
Send Check Digit G
Send Check Digit G
Send Check Digit G
Do Not Send Check Digit H
Do Not Send Check Digit H
Send Check Digit G
SELECTION CODE: G1
Expand UPC-E I
Do Not Expand UPC-E J
Expand UPC-E I
Do Not Expand UPC-E J
Do Not Expand UPC-E J
SELECTION CODE: G1
Send Number Digit E
Do Not Send Number Digit F
Send Number Digit E
Send Number Digit E
Send Number Digit E
Send Number Digit E
Do Not Send Number Digit F
Send Number Digit E
- Keyboard Wedge 1
- USB/Keyboard Wedge 1
- Combined Bar Code 1
- Magnetic Stripe Reader 1
- Agency Approved 2
- Limited Warranty 2
- Table of Contents 3
- Section 1 5
- INTRODUCTION 5
- Description 5
- Section 2 6
- INSTALLATION 6
- Host Connections 6
- Section 3 7
- OPERATION 7
- Operating Procedure 7
- Section 4 8
- CONFIGURATION 8
- Configuration Setup Procedure 8
- Default Settings 10
- General Selections (Group B) 11
- Beep Volume 12
- Intercharacter Delay 12
- Interblock Delay 12
- Language 13
- Code/Track ID 13
- Scan Verification 13
- Function Code 13
- Code ID Definition (Group I) 14
- Bar Code Terminator Character 15
- Bar Code Preamble 16
- Bar Code Postamble 16
- Magnetic Stripe Preamble 18
- Magnetic Stripe Postamble 18
- Bar Code Selections 19
- Code 39 Settings: 20
- Check Digit 21
- Send Start/Stop Characters 21
- Interleaved 2 of 5 Settings: 22
- Industrial 2 of 5 Settings: 23
- FEBRABAN Conversion: 24
- Code 128 Setting: 24
- Codabar Settings: 25
- MSI/Plessey Settings: 26
- Telepen Setting: 26
- Retail Bar Codes (Group G) 27
- UPC Settings: 27
- Enable/Disable UPC-E 28
- Send Number System Digit 28
- Send Check Digit 28
- UPC-E Expansion 28
- EAN Settings: 30
- Read Two-Digit Addendum 31
- Read Five-Digit Addendum 31
- Addendum Required 31
- Add Separator Space 31
- Track Selection 32
- Send Start/Stop Sentinel 32
- Track Separator 33
- Section 5 35
- DATA EDITING 35
- Data Fields 36
- Data Editing Formulas 37
- The Formula Sequence 38
- Data Editing Commands 40
- Select Code ID(s) 41
- Set Length 41
- Match String 42
- Create a Data Field 42
- Search for a Data String 43
- Add a Data Field 43
- Time Delay 44
- Delete One Formula 44
- Omni Data Flow 45
- 76440057320712 46
- *AST798X* 47
- EXAMPLE THREE 48
- Section 6 49
- TROUBLESHOOTING 49
- General Procedures 49
- Keyboard Interface Problems 50
- Appendix A 52
- BAR CODE DEFAULT SETTINGS 52
- Appendix B 55
- Appendix C 56
- FUNCTION CODE TABLE 56
- Appendix D 57
- FORMATS 57
- Card Format 57
- Appendix E 61
- CONNECTOR PIN-OUTS 61
- Appendix F 62
- USB/KEYBOARD INTERFACE 62
- Installation 62
- Operation 63
- 10721 Walker Street 64
- Cypress, California 90630 64
- (714) 761-6368 64
Related products and manuals for Magnetic card readers ID TECH Omni
(4 pages)© 2020, manymanuals.com. All rights reserved. | 0.933 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals