ID TECH Omni User Manual Page 19
- Page / 64
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
15
Bar Code Selections
Bar code selections for the Omni are separated into two groups: Industrial
and Retail. Industrial bar codes may contain a variable number of characters.
Retail bar codes always contain a specifi c number of characters.
Industrial Bar Codes (Group F)
Industrial Bar Codes (Group F)
1. Enter INDUSTRIAL BAR CODE SETUP MODE by typing
/E/D/FF
.
2. Press
<ENTER>
.
The reader should beep twice.
3. Type the two-character selection code for the bar code symbology you wish
to change.
4. Press
<ENTER>
.
The reader should beep twice.
5. Type the one-character code for the change you wish to make.
6. Press
<ENTER>
.
The reader should beep twice.
7. Save the change and exit the Industrial Bar Code Setup Mode by typing
FZ
.
8. Press
<ENTER>
.
The reader should beep four times.
Note: To review the group’s current setting(s), type FY<ENTER> while in the Indus-
trial Bar Code Setup Mode. To reset the current setting(s) to its group default, type
FX<ENTER> while in Industrial Bar Code Setup Mode.
Minimum and Maximum Length Options
You can set minimum and maximum length standards for a particular indus-
trial bar code symbology. (You cannot set a minimum or maximum length for
a retail bar code.)
Minimum length sets the minimum number of data characters that will be
accepted for this symbology. If the minimum length is set higher than the
maximum length, all readings will be rejected.
Maximum length sets the maximum number of data characters that will be
accepted for this symbology. If the maximum length is set lower than the
minimum length, all readings will be rejected.
To set the minimum and maximum length for a particular symbology:
1. Enter Setup Mode by typing
/E/D/FF
.
2. Press
<ENTER>
.
The reader should beep twice.
3. Enter the selection code for the particular symbology selected (such as
F4<ENTER>
for Code 128).
The reader should beep twice.
4. Enter
FU<ENTER>
for minimum or
FV<ENTER>
for maximum.
The
reader should beep twice.
- Keyboard Wedge 1
- USB/Keyboard Wedge 1
- Combined Bar Code 1
- Magnetic Stripe Reader 1
- Agency Approved 2
- Limited Warranty 2
- Table of Contents 3
- Section 1 5
- INTRODUCTION 5
- Description 5
- Section 2 6
- INSTALLATION 6
- Host Connections 6
- Section 3 7
- OPERATION 7
- Operating Procedure 7
- Section 4 8
- CONFIGURATION 8
- Configuration Setup Procedure 8
- Default Settings 10
- General Selections (Group B) 11
- Beep Volume 12
- Intercharacter Delay 12
- Interblock Delay 12
- Language 13
- Code/Track ID 13
- Scan Verification 13
- Function Code 13
- Code ID Definition (Group I) 14
- Bar Code Terminator Character 15
- Bar Code Preamble 16
- Bar Code Postamble 16
- Magnetic Stripe Preamble 18
- Magnetic Stripe Postamble 18
- Bar Code Selections 19
- Code 39 Settings: 20
- Check Digit 21
- Send Start/Stop Characters 21
- Interleaved 2 of 5 Settings: 22
- Industrial 2 of 5 Settings: 23
- FEBRABAN Conversion: 24
- Code 128 Setting: 24
- Codabar Settings: 25
- MSI/Plessey Settings: 26
- Telepen Setting: 26
- Retail Bar Codes (Group G) 27
- UPC Settings: 27
- Enable/Disable UPC-E 28
- Send Number System Digit 28
- Send Check Digit 28
- UPC-E Expansion 28
- EAN Settings: 30
- Read Two-Digit Addendum 31
- Read Five-Digit Addendum 31
- Addendum Required 31
- Add Separator Space 31
- Track Selection 32
- Send Start/Stop Sentinel 32
- Track Separator 33
- Section 5 35
- DATA EDITING 35
- Data Fields 36
- Data Editing Formulas 37
- The Formula Sequence 38
- Data Editing Commands 40
- Select Code ID(s) 41
- Set Length 41
- Match String 42
- Create a Data Field 42
- Search for a Data String 43
- Add a Data Field 43
- Time Delay 44
- Delete One Formula 44
- Omni Data Flow 45
- 76440057320712 46
- *AST798X* 47
- EXAMPLE THREE 48
- Section 6 49
- TROUBLESHOOTING 49
- General Procedures 49
- Keyboard Interface Problems 50
- Appendix A 52
- BAR CODE DEFAULT SETTINGS 52
- Appendix B 55
- Appendix C 56
- FUNCTION CODE TABLE 56
- Appendix D 57
- FORMATS 57
- Card Format 57
- Appendix E 61
- CONNECTOR PIN-OUTS 61
- Appendix F 62
- USB/KEYBOARD INTERFACE 62
- Installation 62
- Operation 63
- 10721 Walker Street 64
- Cypress, California 90630 64
- (714) 761-6368 64
Related products and manuals for Magnetic card readers ID TECH Omni
(4 pages)© 2020, manymanuals.com. All rights reserved. | 0.862 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals